Skip to content
Prospaplans Ltd logoPROSPAPLANS

Land & Engineering

Engineering Surveys & Setting-Out

Putting the design on the ground accurately and keeping it there. Control, setting-out, dimensional checks and re-establishment of control that has been lost, all delivered from a framework that other contractors can use.

Typical accuracy · ±10mm horizontal, ±8mm vertical, proved before setting-out begins.

Setting-out pins and sight rails on a slab
GRAVESEND · SETTING-OUT

When you need it

  • →A structure is being set out and the stakes in the ground are wrong.
  • →You need setting-out drawings and a surveyor on site to mark them.
  • →Control has been destroyed by another contractor and work has stopped.
  • →A dimensional check is needed before a pour or a precast lift.

What you get

  • Control network on OSGB36, established or recovered
  • Setting-out drawing and marked-up dimension sheet
  • On-site marking of the design positions
  • As-marked and as-built dimension check records
  • Control handover for other contractors

How it runs

  1. 01

    Review the design drawings and coordinate system used by the designer.

  2. 02

    Establish or recover control and agree the datum with the contractor.

  3. 03

    Set out and mark, with the contractor present where possible.

  4. 04

    Check as-built against design and issue the record.

Horizontal control
±10mm typical
Vertical control
±8mm typical
Datum
OSGB36 · EPSG:27700
Area covered
Norfolk base · 6 regions

Questions we get asked

My contractor says they set out themselves. Is that allowed?

It is your contract, not ours. But most disputes on site come from two parties using different control and different assumptions. An independent setting-out check costs very little against a structural error.

Where we cover

Norfolk based, working nationwide. Site-based surveying, so distance is rarely the constraint.

Most requested in Lincolnshire & the Midlands, Greater London, South East London.

Every town, district and borough we cover is listed in full on each region page. See the full service area.

All 18 other services

Topographic & Land SurveysLevels, contours and site detail for planning, design and construction.Level Surveys & Site GradientsAccurate falls and cross-falls, including Kent's shrink-swell clay.Measured Building SurveysMeasured floor plans for architects, conveyancing and party wall work.Boundary & Site ControlBoundary definition and setting-out control to RICS standard.Expert Witness & Boundary Dispute ReportsIndependent evidence for boundary disputes and neighbour conflicts.Drainage & Flood Risk SurveysFlood zone assessment and drainage run-off measurement.Construction Progress MonitoringRegular site measurement tracking progress, volumes and change.As-Built & Completion SurveysFinal measured records for handover and compliance sign-off.Drone PhotogrammetryAerial reconstruction producing accurate 3D models and imagery.Aerial Mapping & OrthomosaicsGeoreferenced, distortion-free imagery from a single flight.Point Clouds & 3D ModelsDeliverables in E57, LAZ, LAS, IFC and XYZ for your software.Volumetric & Stockpile SurveysInstant stock tonnage, cut and fill volumes from measured data.LiDAR & 3D Laser ScanningMillimetre-accurate point clouds that reach beneath vegetation.Biodiversity Net Gain SurveysBNG baseline, condition and monitoring evidence from the air and the ground.Multispectral & Agricultural SurveyNDVI and NDRE analysis to reveal crop stress and irrigation issues.Roof Surveys & Aerial InspectionsCondition surveys of roofs and structures without scaffolding.Dropped Object InspectionRecorded and verifiable inspection regime for dropped objects.Thermal & Insulation InspectionLocate heat loss, failed insulation and water ingress before it spreads.

Start here

Send the address and what it is for.

You will get a straight answer on whether this survey is the right one, and what it should cost. If it is not, we will say so.

info@prospaplans.com · Norfolk, Kent, London, East Anglia and the Midlands

CallGet a quote